Brocade Communications Systems Network Advisor 12.0.0 Скачать руководство пользователя страница 570 | Manualshive

Страница: 570 / 1505

background image

522

Brocade Network Advisor SAN User Manual

53-1002696-01

Configuring Virtual Fabrics

19

Leave this check box blank to allow the domain ID to be changed if a duplicate address exists.

8. Click OK on the New Logical Fabric Template dialog box.

The new logical fabric template displays under the Discovered Logical Switches node in the
Existing Logical Switches list (already highlighted).

All of the logical fabric templates have the same name, “NewFabric”. You can differentiate
among the templates by the FID number.

You can now create logical switches using the fabric-wide settings in the logical fabric
template. To assign logical switches, refer to

“Creating a logical switch or base switch”

on

page 516.

NOTE

When you close the Logical Switches dialog box, the logical fabric templates are automatically
deleted. Create the logical switches first, before closing the dialog box, to use the template.

Applying logical fabric settings to all associated logical switches

You can apply a selected logical switch configuration to all logical switches in the same fabric. This
configures the fabric parameters for the selected logical switch to all logical switches in the fabric.

1. Select Configure > Virtual Fabric > Logical Switches.

The Logical Switches dialog box displays.

2. Right-click anywhere in the Existing Logical Switches list and select Table > Expand All.

3. Right-click the logical switch for which you have configured logical fabric settings from the

Existing Logical Switches list and select Configure All.

The logical fabric configuration settings (Fabric tab) are applied to all logical switches in the
same fabric (determined by FID).

4. Click OK on the Logical Switches dialog box.

The Logical Switch Change Confirmation and Status dialog box displays with a list of all
changes you made in the Logical Switches dialog box.

The Re-Enable ports after moving them and QoS disable the ports while moving them check
boxes are selected by default.

NOTE

Ports are disabled before moving from one logical switch to another.

5. (

Optional

) Select the Unbind Port Addresses while moving them check box.

6. Click Start to send these changes to the affected chassis.

NOTE

Most changes to logical switches will disrupt data traffic in the fabric.

The status of each change is displayed in the Status column and Status area in the dialog box.

7. When the changes are complete, click Close.

«
...
568
569
570
571
572
...
»

Содержание Network Advisor 12.0.0


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Network Advisor 12.0.0

RESIDENT CONSULTANT

Бренд: Juniper Страницы: 4

Бренд: TC Electronic Страницы: 12

VFABRIC GEMFIRE

Бренд: VMware Страницы: 2

CONTRIBUTE 3 - USING AND ADMINISTERING...

Бренд: MACROMEDIA Страницы: 256

Smart Wireless Navigator

Бренд: Emerson Страницы: 22

Бренд: Emerson Страницы: 130

Бренд: Kenwood Страницы: 40

Бренд: Art & Logic Страницы: 2

Бренд: Extron electronics Страницы: 37

SmartCell ZX-250

Бренд: Cabletron Systems Страницы: 34

Бренд: CAKEWALK Страницы: 604

Бренд: Nortel Страницы: 93

ANTI-VIRUS 5.6 - FOR MICROSOFT ISA SERVER 2000 ENTERPRISE...

Бренд: KAPERSKY Страницы: 104

Бренд: Samsung Страницы: 13

Бренд: Navman Страницы: 15

Бренд: Navman Страницы: 36

Web GUI RAID Management Tools

Бренд: Sans Digital Страницы: 1

Бренд: Epson Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды