Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 85

Страница: 85 / 304

Fig.6-6:

Adjustment screen: Axes

If the adjustment has been successfully completed, the adjustment symbols

and the text are removed from the table.

Adjustment screen: Spindles

The screen comprises three partial windows. The upper partial window displays

the total adjustment information of all data types and the target block for a better

overview.
The partial window in the middle visualizes the adjustment state of each indi‐

vidual axis as spindle.
There are two views (switching via <F7>):
●

The adjustment information and the expected command values are shown

in their interrelation.

●

All adjustment information is displayed as compressed and the expected

command value for the adjustment is shown depending on the focused

line of the adjustment information.

All functions to be adjusted have to be provided with an adjustment symbol.

The adjustment reason is given as text
If the spindle S1 rotate into the wrong direction for example, this is indicated by

the text "Incorrect motion function". The command value indicates the reques‐

ted direction.
A maximum of three spindles can be shown side by side. In case of more than

three spindles, a scrollbar is shown.
The lower partial window visualizes the adjustment state of each the spindle

couplings. If no spindle coupling is active, the lower partial window is hidden.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

83/301

Operation Modes

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 85 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: