Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 41

Страница: 41 / 304

●

Actual speed (only ACS; available only for asynchronous, endlessly turn‐

ing round axes, otherwise 0)

●

Maximum velocity (only ACS)

The display supports a maximum of 10 variants.
If a date is not available, "—" is displayed.

The following table contains a description of the symbols displayed.

Symbol Meaning

Note

Coordinate system

symbols

ACS

Axis coordinate system

MCS

Machine coordinate system

BCS

Basic coordinate system

WCS

Tool coordinate system

Position symbols

Axis is not referenced

The reference position of the axis is not known.

Axis is in position

The axis is located in the given position window.
This symbol is only shown if the reference position of the

axis is known.

Channel assignment

symbols

1...12

Channel number

Asynchronous axis

S-0-0124

Spindle

Spindle inactive

Axis not defined

Unit symbols

metric

inch

non-metric

Degrees

∅

Diameter programming

Location programming

None

Fig.5-3:

Displayed symbols

Coordinates

The following figure shows an overview of the coordinates / axis positions that

can be displayed.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

39/301

General Operation and Visualization

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 41 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: