Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 177

Страница: 177 / 304

Fig.8-18:

Tool management screen with two tables (screen layout, horizontal 1:2)

Functions in the Tool List Display

The functions of the F-keys are described in the corresponding table editor.

Retrieval of the tool editor for creating a new tool data set. You can switch back

to the tool list by clicking the mouse in the taskbar. However, the task bar cannot

be edited because the database remains blocked. The list can be edited only

after the new tool editor has been closed.
The function can also be opened via the following menu function in the default

configuration Edit ▶ Insert tool .

Retrieval of the tool editor for editing an existing tool data set. You can use the

task bar to return to the tool list; the database does not remain locked. However,

the <F5 Edit tool function> can be retrieved again only after the tool editor is

exited.
The function can also be opened via the following menu function in the default

configuration Edit ▶ Edit tool .

The tool data record can be deleted in the database by confirming the prompt

"Delete tool".
The function can also be opened via the following menu function in the default

configuration Edit ▶ Delete tool .

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

175/301

Tool Management

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 177 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: