Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 174

Страница: 174 / 304

Column

Displayed data ele‐

ment

Always

visible

Can be edi‐

ted

Special features

Range

Tool status

Main column

Scrollable

6.1

Tool active (ta)

Yes

Checkbox display

6.2

Tool used (tu)

Yes

6.3

Warning limit reached

(tw)

Yes

6.4

Tool worn (two)

Yes

6.5

Tool blocked (TB)

Yes

6.6

Tool defective (TD)

Yes

6.7

(TTL)

Yes

6.8

(TTU)

Yes

6.9-6.12 Tool user status

Yes

Location status

Main column

7.1

Location blocked (PB) Yes

Yes

Checkbox display

7.2-7.4

Location user status

Yes

Fig.8-16:

Contents of the status list

Displaying several lists in one

screen

Several differently configured lists can be displayed in one tool management

screen.
One of the following display variants can be selected when configuring the

screen. The dimensions of the lists cannot be modified.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

172/301

Tool Management

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 174 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: