Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 304

Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 131

After selecting and opening the file to be imported, the menu allowing the se‐

lection of the cycle ranges to be imported is shown.

Fig.7-7:

Selection of the cycle ranges to be imported

The OEM or User selection boxes are grayed out if there are no

files for the respective ranges in the import file.

After the cycle range to be imported has been selected, the files are saved in

the paths reserved for the cycle ranges. If the paths do not exist, they are cre‐

ated. If a file does already exist with the same name, a dialog asks for

confirmation (Do you want to overwrite this file?).

Fig.7-8:

Exchange in case of existing file

7.3

Variable Editor

7.3.1

Overview

Variable Editor

The variable editor visualizes the following variables:
●

Permanent variables (@)

●

Definable permanent variables (@)

●

System data (SD)

Screen Layout

Structure

The variable editor consists of the columns "Name", "Value" and "Comment".
In the "Edit online" mode under the operating area "Machine" <OP3>, the col‐

umns "Name", "Value" (control), "Value" (list) and comment are displayed.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

129/301

Programming

«
...
129
130
131
132
133
...
»

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов