Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 235

Страница: 235 / 304

11.1.4

Operating Principle of the NC-Analyzer

General

The following summary shows the operating principle when working with the

NC-Analyzer:

Con.

no.

Procedure

Selecting a program

Starting the NC-Analyzer

Loading configuration file (optional)

Selecting channel (optional)

Navigating to the incorrect program part or to the subroutine in the NC-Ana‐

lyzer if required

Setting breakpoints at possible error locations

Selecting variables for monitoring

Starting NC program

Monitoring the values of the selected variables and the error analysis

Error clearance of the respective program parts in the control editor

Testing the program regarding error recovery.
... and whether more errors are present

Saving configuration (settings) or any subsequent NC-Analyzer sessions

Selecting the Program

The program selection is opened via the OP-key "Machine" of <F2>. Select the

NC program to be run.
●

Only one program can be edited at a time.

●

To edit a program, the file attribute of the program needs to be configured

accordingly. In the "File" window, each file is prefixed with a symbol for

the file attribute.

●

The program displayed in the NC-Analyzer can only be edited there if it is

active in the selected control and the set channel.

●

If the selected program is edited in the control, all changes also become

active immediately in the NC-Analyzer (incl. monitored variables and sub‐

routines).

Loss of data!
●

If a different program is selected for processing, this is also

loaded into the NC-Analyzer at the same time. Changes in the

previous program will be lost.

●

The command "Reset channel" in the control means that

breakpoints and monitored variables are lost.

Channel Selection

The F-key <F2 channel selection> can be used to switch the channel in the NC-

Analyzer.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

233/301

Extended Functionality

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 235 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: