Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 195

Страница: 195 / 304

Diagnostics

10.1

Diagnostic Display

10.1.1

Overview

Press <OP9> to activate the diagnostic display.

The delivery scope of IndraWorks HMI depends on the installed

control system. In contrast to the fact that the IndraMotion MTX

provides already existing screens to operate NC machines, an

IndraLogic control is only provided with the <OP9> key to which the

diagnostic call is assigned.

Fig.10-1:

Start screen of the diagnostics

The start screen of the diagnostics is divided into four areas:

Message list field (1)

The diagnostic messages of the assigned control (see header) are displayed

here. Listed are:
●

the message number

●

the existence of criteria analysis data (CA)

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

193/301

Diagnostics

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 195 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: