Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 75

Страница: 75 / 304

Fig.5-47:

Precision corrections

5.6.3

Operation and Navigation

The operation is executed via F-keys.

Switching between the

screens

It is switched between the four screens using <F2>, <F3>, <F4> and <F5>.

Basic level of the F-keys

Apart from the shift keys for the four screens, there are further important func‐

tions in the basic level related to the corrections.

<F2>
Correction

overview 1

<F3>
Correction

overview 2

<F4>
Tool correc‐

tion register

<F5>
Precision cor‐

rections

<F6>
Zero point off‐

sets

<F7>
Active D-cor‐

rections

<F8>
More func‐

tions...

<F9>
Exit correc‐

tions

Opening the

screen "Cor‐

rection over‐

view 1"

Opening the

screen "Cor‐

rection over‐

view 2"

Opening the

screen "Tool

correction

Opening the

screen "Preci‐

sion correc‐

tions"

Opening the

editor for

"zero point

offsets"

Opening the

editor for "ac‐

tive D-correc‐

tions"

Additional

functions

(2nd level)

Application

"Complete"

Fig.5-48:

Basic level of the F-keys

F-keys, Additional functions

This level contains additional functions.

<F2>
Reset chan‐

nel

<F3>
System reset

<F4>

<F5>

<F6>

<F7>
Active°

<F8>
Return

<F9>

"Reset chan‐

nel" function

"Reset sys‐

tem" function

Focus partial

window

Return

basic level

Fig.5-49:

F-keys, Additional functions

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

73/301

General Operation and Visualization

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 75 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: