Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 115

Страница: 115 / 304

Programming

7.1

Overview

NC program creation is described in this chapter.

Fig.7-1:

"Programming" operating area

7.2

NC Program Creation

7.2.1

Overview

NC program creation is conducted with the NC program editor. The NC program

editor can be opened several times in the operating area if required, to open

several NC programs. The NC program editor is aligned with the Windows

standard with regard to the usual key combinations (selecting, block com‐

mands, search, etc.).
It has the following basic characteristics:
●

Basic mechanisms to avoid data loss (BAK files).

●

Navigation: character by character, word by word, line by line, start, end

and via search function.

●

Slider function using slider bar, slider mouse, cursor positioning and keys.

●

Selection: character by character, word by word, line by line, entire file.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

113/301

Programming

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 115 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: