Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 218

Страница: 218 / 304

●

Software version of the MTX kernel

●

Software version of the subsystems

●

Version information on the Windows software components

Fig.10-38:

Information on the Firmware

Software version of the MTX kernel

Returns information on the general software version of the MTX kernel as well

as a copyright message (version of the basic software and the customer up‐

grades).

Software version of the subsystems

Provides information on software versions of the subsystems in the MTX kernel.

The following data is provided for each subsystem:
●

Subsystem name

●

Release number

●

Time stamps

Windows software components

Provides version information on the Windows software components which (un‐

der Windows) provide the communication interface for the MTX kernel. included

is:
●

the NCS interface (ncstyp3.dll),

●

the text management (tsvtyp3.dll),

●

the logical device MTX
(SCPBricDevice.dll, SCPBricComponent.dll) and

●

FIS (FisServer.dll).

The following data is provided for each component:
●

Subsystem name

●

Release number

●

Time stamps

10.6.7

Startup Configuration

Startup

MTX starts while switching on the control or while triggering an NC restart. The

startup occurs synchronized in 12 phases displayed in the MTX system status:

P: -3

Determining the existing hardware

P: -2

RTOS startup, configure file systems

P: -1

Start RTOS monitor

P: 1

Initialize basic NCS communication

P: 2

Initialize TCP/IP

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

216/301

Diagnostics

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 218 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: