Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 247

Страница: 247 / 304

Error message number and message

text number

Cause

Recommended to the user

(#32)
The current NC mode cannot be deter‐

mined.
(INcsChannel::GetNcMode)

Timeout too short.

Close and restart the application.

(#50)
The depth of the call stack cannot be de‐

termined.
(IProgChain::GetProgChainDeep)

Timeout too short.

Close and restart the application.

(#51)
The parameters of a subroutine cannot

be determined.
(IProgChain::GetSubProgLevel)

Timeout too short.

Close and restart the application.

(#80)
The connection to the NC was interrup‐

ted.

The connection to the NC was interrup‐

ted.

Close the application, restart it and rees‐

tablish the connection.

(#69)
Failed to establish a connection to the

NC.
(INcConnect::Connect)

Failed to establish a connection to the

NC.

Close the application, restart it and rees‐

tablish the connection.

(#33)
The requested NC mode cannot be set.
(INcsProcess::SetOpMode)

NC mode was changed (e.g. by another

application).

Continue and set the desired NC mode

after a new selection and after starting

the required flow program.

Fig.11-7:

Message reasons are: either OLE error, software problems of the NC

application or MTX-Analyzer application or installation problems

Abbreviations

Numerical Control (System)

CNC

Computerized Numerical Control

CPL

Customer Programming Language

Personal Computer

DDP

Desktop Development Platform

SCP

Scalable Communication Platform

11.2

Energy Monitor

11.2.1

Overview

Purpose of the Energy Monitor

With the energy monitor, the energy consumption of a machine as well as of

individual function modules (electric drives and auxiliary equipment (hydraulic

pumps, cooling lubricant system etc.) are summed up and monitored over de‐

fined time spans.
The energy monitor is part of the MTX interface.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

245/301

Extended Functionality

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 247 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: