BLEMO ER24 Series, Руководство по программированию

Страница: 63 / 344

Monitoring Mode (MOn)
65
Code Nam e / De s cription Unit
InFA [Inte rnal-m ains circuit] (InFA) : Input phase loss circuit detected error
InFb [Inte rnal- th. s e ns or] (InFb) : Thermal sensor detected error (OC or SC)
InFE
[Inte rnal-CPU]
(InFE) : CPU detected fault (ram, flash, task ...)
LCF [Input contactor] (LCF) : Line contactor detected error
LFF3 [AI3 4-20m A los s ] (LFF3) : AI3 4-20 mA loss
ObF
[Ove rbrak ing]
(ObF) : Overbraking
OCF [Ove rcurrent] (OCF) : Overcurrent
OHF [Drive ove rheat] (OHF) : Drive overheating
OLC
[Proc.Ove rload Flt]
(OLC) : Torque overload
OLF [M otor ove rload] (OLF) : Motor overload
OPF1 [1 output phase los s] (OPF1) : Motor 1-phase loss
OPF2
[3out ph los s]
(OPF2) : Motor 3-phases loss
OSF [M ains overvoltage] (OSF) : Oversupply detected fault
OtFL [PTC fault] (OtFL) : Motor overheating detected error from PTCL: standard product
PHF
[Input phase los s]
(PHF) : Main input 1-phase loss
PtFL [LI6=PTC probe ] (PtFL) : PTCL detected error (OC or SC)
SAFF [Safe ty] (SAFF) : Safety function
SCF1
[M otor s hort circuit]
(SCF1) : Motor short circuit (hard detection)
SCF3 [Ground s hort circuit] (SCF3) : Direct ground short-circuit (hard detection)
SCF4 [IGBT s hort circuit] (SCF4) : IGBT short-circuit (hard detection)
SCF5
[M otor s hort circuit]
(SCF5) : Load short-circuit during Igon load sequence (hard detection)
SLF1 [M odbus com .] (SLF1) : Modbus local serial communication interruption
SLF2 [PC com .] (SLF2) : PC Softw are communication interruption
SLF3
[HM I com .]
(SLF3) : Remote terminal communication interruption
SOF [Ove rs pe e d] (SOF) : Overspeed
SPF [Spe e d fdback loss] (SPF) : Speed feedback loss
SSF
[Torque/current lim ]
(SSF) : Torque current limitation detected fault
tJF [IGBT ove rhe at] (tJF) : IGBT overheating
tnF [Auto-tuning] (tnF) : Tune detected fault
ULF
[Pr.Unde rload Flt]
(ULF) : Torque underload
USF [Unde rvoltage ] (USF) : Undervoltage
HS1 [Drive state]
HMI Status of the detected fault record 1.
tUn
[Auto-tuning]
(tUn) : Auto-tuning
dCb [In DC inje ct.] (dCb) : Injection braking
rdY [Re ady] (rdY) : Drive ready
nSt
[Fre e w heel]
(nSt) : Freew heel stop control
rUn [Drv running] (rUn) : Motor in steady state or run command present and zero reference
ACC [In acce l.] (ACC) : Acceleration
dEC
[In de ce l.]
(dEC) : Deceleration
CLI [Curre nt lim .] (CLI) : Current limit
(in case of using a synchronous motor, if the motor does not start, follow the procedure page 112 )
FSt [Fas t s top] (FSt) : Fast stop
FLU [M ot. fluxing] (FLU) : Fluxing function is activated
nLP [no m ains V.] (nLP) : Control is pow ered on but the DC bus is not loaded
CtL
[control.s top]
(CtL) : Controlled stop
Obr [De c. adapt.] (Obr) : Adapted deceleration
SOC [Output cut] (SOC) : Stand by output cut
USA
[Unde rV. al.]
(USA) : Undervoltage alarm
tC [In m fg. te s t] (tC) : TC indus mode activated
St [in autote s t] (St) : Self test in progress
FA
[autote st e rr]
(FA) : Self test detected error
YES [Autotest OK] (YES) : Self test OK
EP [e e prom test] (EP) : Self test Eeprom detected error
FLt
[In fault]
(FLt) : Product has detected a fault
SS1 [SS1 active ] (SS1) : Safety function SS1
SLS [SLS active ] (SLS) : Safety function SLS
StO
[STO active ]
(StO) : Safety function STO
SMS [SM S active ] (SMS) : Safety function SMS
GdL [GdL active ] (Gdl) : Safety function GdL
Ep1 [ETA state word]
DRIVECOM status register of detected fault record 1 (same as
[ETA s tate word]
(EtA) page 57 ).
IP1 [ETI state word]
Extended status register of detected fault record 1 (see the communication parameters file).
Parameters described in this page can be accessed by:
DRI- > MON- > DGT- > PFH-