Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 90

Страница: 90 / 124

2. Select the H

Hot water heating parameter by turning the

button.

3. Press the button to confirm.

4. Select the appropriate operating mode.

See

Shortcuts menu, page 71.

5. Press the button to confirm.

Note

Press the

key to return to the main display.

9.2.7 Setting the domestic hot water temperature set point

1. Press the

key to access the shortcuts menu.

2. Select the H

Hot water temp setpoint parameter by turning the

but

ton.

3. Press the button to confirm.

4. Turn the

button to modify the temperature set point.

See

Shortcuts menu, page 71

5. Press the button to confirm.

Note

Press the

key to return to the main display.

9.2.8 Setting the room temperature set point (Reduced mode)

1. Press the

key to access the parameters.

2. Select the TTemps / mode CH1 menu by turning the

button.

Fig.89

MW-3000064-EN-02

MENU

Room temperature CH3

Hot water mode

Hot water temp setpoint

Fig.90

MW-3000066-EN-02

MENU

Hot water mode

Hot water temp setpoint

----------------------------------------------------

Fig.91

MW-3000067-EN-02

MENU

Hot water temp setpoint

9 Settings

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды