Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 104

Страница: 104 / 124

11. Select a target day by turning the

button.

12. Confirm the menu selection by pressing the button .

Note

Repeat the copy to other days if necessary.

Press the

key to return to the main screen.

Reset the timer programmes to zero

1. Press the

key to access the parameters.

2. Select the TTime central heating CH1 menu by turning the

button.

Note

For heating circuits 2 and 3, select the parameters TTime central

heating CH2

or TTime setting 3/CHP.

For the domestic hot water circuit, select the parameter TTime

hot water.

3. Confirm the menu selection by pressing the button .

The parameter S

Select days (500, 520, 540 or 560) is displayed.

4. Select the parameter D

Default values (516, 536, 556 or 576) by turn

ing the

button.

5. Confirm the parameter selection by pressing the button.

The parameter N

No flashes.

Fig.

128

MW-3000140-EN-02

MENU

Tuesday

Copy to

Time central heating CH1

Monday

Fig.

129

MW-3000071-EN-02

MENU

----------------------------------------------------

Information

Set time and date

Fig.

130

MW-3000141-EN-02

MENU

Time central heating CH1

Default values

9 Settings

104

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды