Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 109

Страница: 109 / 124

9. Remove the fan, the Venturi and the burner to access the inside of

the heat exchanger.

110.2.3 Cleaning the heat exchanger

1. Remove the burner.

See

Removing the burner, page 107.

2. Clean the pipes inside the heat exchanger using ordinary vinegar.

3. Flush with water.

Note

The water will exit the heat exchanger by passing through the con

densates discharge siphon.

4. After twenty minutes, wash off any dirt with a powerful water spray.

Caution

Be careful not to direct the spray straight at the insulating surface

behind the heat exchanger.

5. Dry the heat exchanger.

6. Check the burner.

See

Checking the burner, page 109

7. Clean the siphon.

See

Cleaning the siphon, page 111

8. Remount the burner.

See

Remounting the burner, page 111

10.2.4 Checking the burner

1. Remove the burner.

See

Removing the burner, page 107.

Fig.

139

Removing the fan, the collector and

the burner

-3000109-01

Fig.

140

Cleaning the exchanger

-3000100

Fig.

141

Spray cleaning

-3000101

10 Maintenance

7609474 - v02 - 04092014

109

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды