Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 114

Страница: 114 / 124

Checking combustion (reduced thermal flow rate)

1. Unscrew the plug in the flue gas measurement point.

2. Connect the flue gas analyser.

Note

Ensure that the opening around the sensor is completely sealed

when taking measurements.

Insert the sensor into the flue gas measurement point opening

to at least 8 cm for POWER HT+ 1.50 and POWER HT+ 1.70.

Insert the sensor into the flue gas measurement point opening

to at least 9 cm for POWER HT+ 1.90 and POWER HT+ 1.110.

3. Set the boiler's thermal flow rate to 0%.

See

Using the boiler according to thermal output, page 94.

4. Measure the percentage of CO

in the flue gases.

5. Compare the values measured with the set point values in the Con

trol and setting values table.

See

CO2 checking and setting values, page 62.

Note

A tolerance of +/- 0.5% is acceptable when the front panel is

closed.

6. If necessary, modify the air/gas ratio.

See

Setting the air/gas ratio (maximum thermal flow rate), page 59.

Fig.

148

Connecting the flue gas analyser

MW-3000112-01

10 Maintenance

114

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды