Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 89

Страница: 89 / 124

2. Select the 3316:Hot water boost parameter by turning the

button.

3. Press the button to start forcing domestic hot water.

Note

Press the button a second time to stop forcing domestic hot

water.

See

Shortcuts menu, page 71

Note

Press the

key to return to the main display.

9.2.5 Setting the room temperature set point (On mode)

1. Press the

key to access the shortcuts menu.

2. Select the R

Room temperature CH1 parameter by turning the

but

ton.

3. Press the button to confirm.

4. Turn the

button to modify the temperature set point.

See

Shortcuts menu, page 71

5. Press the button to confirm.

Note

Press the

key to return to the main display.

9.2.6 Modifying the domestic hot water production mode

1. Press the

key to access the shortcuts menu.

Fig.86

MW-3000061-EN-02

MENU

----------------------------------------------------

Standby/operation

Hot water boost

Fig.87

MW-3000062-EN-02

MENU

----------------------------------------------------

Standby/operation

Hot water boost

Fig.88

MW-3000063-EN-02

MENU

Room temperature CH1

9 Settings

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды