Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 6

Страница: 6 / 124

1 Safety

11.1 General safety instructions

Danger

If you smell gas:

1. Do not use a naked flame, do not smoke, do not

operate electrical contacts or switches (doorbell,

light, motor, lift, etc.).

2. Shut off the gas supply.

3. Open the windows.

4. Trace possible leaks and seal them immediately.

5. If the gas leak is before the gas meter, contact the

gas supplier.

Danger

If you smell flue gases:

1. Switch off the appliance.

2. Open the windows.

3. Trace possible leaks and seal them immediately.

Warning

Do not touch the flue gas pipes. Depending on the

boiler settings, the temperature of the flue gas pipes

may exceed 60°C.

Warning

Do not touch the radiators for long periods. Depending

on the boiler settings, the temperature of the radiators

may exceed 60°C.

Warning

Take precautions with the domestic hot water. De

pending on the boiler settings, the domestic hot water

temperature may exceed 65°C.

Danger of electric shock

Before any work, switch off the mains supply to the

boiler.

1.2 Recommendations

Note

Keep this document close to the place where the ap

pliance is installed.

Note

Never remove or cover labels and data plates affixed

to the appliances. Labels and data plates must be

legible throughout the entire lifetime of the appliance.

Immediately replace damaged or illegible instructions

and warning stickers.

1 Safety

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды