Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 69

Страница: 69 / 124

3. Select the C

Commissioning menu by turning the

button.

4. Confirm the menu selection by pressing the button .

Note

Press the

key to return to the main display.

The C

Commissioning mode parameters are now accessible. Use the

button to select and modify them.

See

List of installer parameters, page 74.

8.2 Starting up the boiler

1. Start up the boiler by pressing the ON/OFF switch.

2. Open the gas cock.

3. Press the

key to access the shortcuts menu.

4. Select the S

Standby/operation parameter by turning the

button.

5. Press the button to start up the boiler.

The symbol disappears.

8.3 Stopping the boiler

Note

Prefer the O

Off or S

Standby operating mode.

See

Activating Protection mode, page 70

Putting the boiler in Standby mode, page 69

1. Switch off the boiler by pressing the ON/OFF switch.

2. Close the gas cock.

8.3.1 Putting the boiler in Standby mode

1. Press the

key to access the shortcuts menu.

2. Select the S

Standby/operation parameter by turning the

button.

3. Press the button to put the boiler in standby.

The symbol is displayed.

Fig.73

MW-3000083-EN-02

MENU

----------------------------------------------------

Enduser

Commissioning

Fig.74

MW-3000084-EN-02

MENU

Enduser

Commissioning

Engineer

Fig.75 Starting up the boiler

MW-3000050

8 Operation

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды