Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 7

Страница: 7 / 124

Caution

The appliance should be on Summer or Antifreeze

mode rather than switched off to guarantee the follow

ing functions:

Anti-blocking of pumps

Frost Protection

Caution

If the home is unoccupied for a long period and there

is a risk of frost, drain the boiler and the heating sys

tem.

Caution

To enjoy warranty cover, no modifications must be

made to the appliance.

Caution

The frost protection does not work if the boiler is

switched off.

Caution

The integrated protection system only protects the

boiler, not the heating installation

Note

Remove the casing only to perform maintenance and

repair work. Put the casing back in place after mainte

nance and repair work.

Warning

Only qualified professionals are authorised to work on

the boiler and the heating installation.

Note

Keep the boiler accessible at all times.

Caution

Installation of the boiler must be done by a qualified

professional in accordance with prevailing local and

national regulations.

Caution

Install the boiler in a frost-free location.

Caution

Do not stock chloride or fluoride compounds close to

the boiler. They are particularly corrosive and may

contaminate the combustive air. Chloride and fluoride

compounds are present in aerosol sprays, paints, sol

vents, cleaning products, washing products, deter

gents, glues, snow clearing salts.

Caution

Do not neglect to service the boiler. Contact a quali

fied professional or subscribe to a maintenance con

tract for the annual servicing of the boiler.

1 Safety

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды