Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 68

Страница: 68 / 124

8 Operation

88.1 Use of the control panel

8.1.1 Modifying the user parameters

1. Press the

key to access the parameters.

Note

Press the

key to return to the main display.

The user parameters can now be accessed. Use the button to se

lect and modify them.

See

List of user parameters, page 72.

8.1.2 Modifying the installer parameters

1. Press the

key to access the parameters.

2. Hold down the

and

keys simultaneously for at least 6 sec

onds.

Fig.70

MW-3000052-EN-02

MENU

14:13

1.5 bar

18. February 2014

Tuesday

MENU

Fig.71

MW-3000052-EN-02

MENU

14:13

1.5 bar

18. February 2014

Tuesday

MENU

Fig.72

MW-3000082-EN-02

MENU

----------------------------------------------------

Information

Set time and date

Information

8 Operation

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды