Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 105

Страница: 105 / 124

6. Select the Y

Yes parameter by turning the

button.

7. Confirm the parameter selection by pressing the button.

Note

Press the

key to return to the main screen.

The reset of the timer program to zero has been successful.

9.2.14 Setting a temporary heating flow temperature

1. From the control panel main screen, turn the button to increase

or reduce the temperature value.

2. Confirm the menu selection by pressing the button .

9.2.15 Managing boilers in cascade

Boilers in cascade are controlled and managed by the lead boiler.

1. Set the following parameters on the lead boiler:

Tab.59 Configuration lead cascade boiler

Parameter num

ber

Parameter

Setting

Description

3540

Auto source seq ch'over

Number of hours

Operating time before the auto

matic change of the lead boiler

sequence.

3541

Auto source seq exclusion

First

First and last

Last

None

Exclusion of the boiler or boilers

from the periodic sequence rota

tion.

See

List of installer parameters, page 74.

9.3 Accessing the information menu

1. Go to the parameters menu by pressing the

key.

Fig.

131

MW-3000142-EN-02

MENU

Yes

Time central heating CH1

Default values

Fig.

132

MW-3000143-EN-02

MENU

Temporary setpoint

9 Settings

7609474 - v02 - 04092014

105

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды