Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 19

Страница: 19 / 124

Note

Please contact us for further information.

4.2.4 Settings and safety devices

Note

The settings and safety devices are only operational if the boiler is

powered up.

Tab.7

Description of the safety devices

Device

Description

Safety thermostats

The safety thermostats suspend the supply of gas to the burner if the water in the pri

mary circuit overheats. To resume normal operation of the boiler, eliminate the cause of

this interruption.

Caution

The safety thermostats must in no circumstances be switched off or

disconnected.

NTC flue gas sensor

The control panel blocks the gas supply to the burner in the event of overheating. To

resume normal operation of the boiler, switch off the boiler and switch it back on again

with the ON/OFF switch.

Flame detector by ionisation

The boiler is put into safety shut-down in the event of gas shortage or incomplete inter

ignition on the burner.

Hydraulic pressure switch

Thanks to this device, the burner can only operate if the system pressure is higher than

0.5 bar (50 kPa).

When the pressure switch detects a pressure lower than 0.8 bar (80 kPa), a warning

message is displayed, without stopping the heating pump.

Post-circulation pump

After the burner stops, depending on the room thermostat setting and if in heating

mode, the heating pump runs for a further 3 minutes.

Antifreeze fluid device

When the flow temperature is lower than 5°C, the burner starts up and runs until the

flow temperature reaches 15°C. This device runs under the following conditions:

The boiler is switched on

The gas supply is working

The pressure in the system is higher than 0.5 bar

Anti-blocking of the pump

If there are no heating or domestic hot water requirements for 24 consecutive hours, the

pumps start up automatically and run for 10 seconds.

The pumps connected directly to the appliance's terminal blocks are started up every

Friday at 10:00 a.m. and run for 30 seconds.

Anticipatory start-up of the circula

tion pumps

In heating mode only, the appliance can start up the circulation pumps before burner ig

nition. The duration and activation of anticipatory start-up depends on the conditions of

installation and the operating temperatures. The duration of anticipatory start-up of the

circulation pumps therefore varies from a few seconds to several minutes.

Fig.8

Boilers in cascade

-3000145-01

4 Description of the product

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды