Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 88

Страница: 88 / 124

4. Confirm the menu selection by pressing the button.

The language currently used flashes.

5. Modify the parameter by turning the button

6. Confirm the setting by pressing the button.

Note

Press the

key to return to the main display.

9.2.3 Changing the operating mode

1. Press the

key to access the shortcuts menu.

2. Select the C

Central heating mode CH1 parameter by turning the

button.

3. Press the button to confirm.

4. Select the appropriate operating mode.

See

Shortcuts menu, page 71

5. Press the button to confirm.

Note

Press the

key to return to the main display.

9.2.4 Forcing domestic hot water production

1. Press the

key to access the shortcuts menu.

Fig.83

MW-3000058-EN-02

MENU

English

Operator section

Change language

Fig.84

MW-3000059-EN-02

MENU

----------------------------------------------------

Standby/operation

Hot water boost

Fig.85

MW-3000060-EN-02

MENU

Timed

Central heating mode CH1

Setting NOT confirmed

9 Settings

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды