manualshive.com logo in svg

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Поделиться
Скачать
Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 55

Fig.63 O

OCI 345 interface connections for cascade

MW-3000042

DB.MB

DB.MB

DB.MB

To make the connections between the various M

MB and D

DB connectors, 

use a shielded cable with the following specifications:

Type

Cross section

Maximum length

HAR H05 VV-F

2 x 1.5 mm

2

200 m

6.7  Filling the system

6.7.1  Filling the heating system

Before filling the heating system, rinse it thoroughly.

See

Flushing an existing installation, page 55.

Flushing new systems and systems less than 6 months old, 

page 55.

In many cases, the heating circuits can be filled with mains water, without 

treating the water.

See

Water treatment, page 23

.

1. Fill the heating system until you reach a pressure of between 1.5 

and 2 bar (0.15 and 0.2 MPa).

2. Check the tightness of the hydraulic connections.

3. Completely vent the heating circuit for optimum running.

Flushing new systems and systems less than 6 months old

1. Clean the installation with a powerful universal cleaner to eliminate 

debris from the appliance (copper, hemp, flux).

2. Thoroughly flush the installation until the water runs clear and shows 

no impurities.

Flushing an existing installation

1. Remove any sludge from the installation.

2. Flush the installation.

3. Clean the installation with a universal cleaner to eliminate debris 

from the appliance (copper, hemp, flux).

4. Thoroughly flush the installation until the water runs clear and shows 

no impurities.

6  Installation

7609474 - v02 - 04092014

55

Содержание POWER HT+ 1.110





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды