Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 58

Страница: 58 / 124

77.3.2 Checking the gas inlet

Note

Ensure that the boiler is switched off.

See

Stopping the boiler, page 69.

1. Open the main gas valve.

2. Open the gas valve on the boiler.

3. Open the front panel.

4. Check the gas supply pressure at the pressure outlet on the gas

valve unit.

See

Gas valves, page 62.

5. Check the tightness of the gas connections made after the gas valve

unit in the boiler.

6. Check the tightness of the gas pipe, including any valves, from the

non-return valve to the burner. The test pressure must not exceed

60 mbar (6 kPa).

7. Vent the gas supply pipe by unscrewing the pressure outlet on the

gas valve unit. Close the outlet again when the pipe has been suffi

ciently vented.

8. Check the tightness of the gas connections in the boiler.

7.3.3 Checking the electrical connections

1. Check the electrical connection to the mains.

2. Check the connection and positioning of the sensors.

3. Check the connection of the circulating pump(s).

7.3.4 Checking the hydraulic circuit

1. Check the siphon, which must be completely filled with water.

2. Check that there are no leaks on the boiler's hydraulic connections.

3. Check the pressure in the expansion vessel before filling the sys

tem.

7.4 Gas settings

7.4.1 Configuring the fan speed

The boiler's fan speed has to be configured according to gas type before

the gas valve is set.

See

Fan speed according to gas type, page 59.

1. Access the installer parameters

See

Modifying the installer parameters, page 68.

2. Select the B

Boiler Settings menu by turning the

button.

3. Confirm the menu selection by pressing the button.

4. Modify parameter 2441 FFan speed heating max according to gas

type. Use the button to select and modify the parameter.

See

Fan speed according to gas type, page 59.

5. Confirm the setting by pressing the button.

6. Select the B

Burner control menu by turning the

button.

7. Modify parameters 9512 R

Required speed ignition, 9524 R

Required

speed LF and 9529 R

Required speed HF according to gas type. Use

the button to select and modify the parameters.

7 Commissioning

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды