Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 26

Страница: 26 / 124

Caution

It is forbidden to store inflammable products and materials in the

boiler room or close to the boiler, even temporarily.

Caution

The boiler must be installed in a frost-free environment.

Make sure there is a connection to the sewage system close to

the boiler to discharge any condensates.

5.3.1 Ventilation

To allow the intake of combustive air, sufficient ventilation must be

provided in the boiler room, for which the cross section and posi

tion must satisfy the regulations in force in the country in which the

boiler is installed:

If the boiler is installed in a closed casing, respect the minimum dimen

sions given in the diagram below. Also allow for openings to obviate the

following hazards:

Accumulation of gas

Heating of the box

Minimum cross section of the openings: S

S1 + S

S2 = 150 cm

Ventilation to be provided for the boilers

Ventilation to be provided for boilers with low-loss header (op

tional)

5.3.2 Dimensions of the appliance

To ensure adequate access to the appliance and facilitate maintenance,

leave enough space around the boiler.

Fig.17 Ventilation to be provided for the

boilers

MW-3000011-01

Fig.18 Ventilation to be provided for boilers

with low-loss header (optional)

MW-3000012-01

5 Before installation

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды