manualshive.com logo in svg

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Поделиться
Скачать
Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 118

12  Decommissioning

112.1  Decommissioning procedure

Warning

Only qualified professionals are authorised to work on the boiler 

and the heating installation.

To switch off the boiler temporarily or permanently, proceed as follows:

1. Switch off the boiler.

2. Cut the electrical power to the boiler.

3. Close the gas valve to the boiler.

4. Drain the central heating system or ensure frost protection.

5. Close the door of the boiler to prevent air circulating inside it.

6. Remove the pipe connecting the boiler to the chimney and close the 

nozzle with a plug.

12.2  Recommissioning procedure

Warning

Only qualified professionals are authorised to work on the boiler 

and the heating installation.

Should it prove necessary to carry out the recommissioning of the boiler, 

proceed as follows:

1. Re-establish electrical power to the boiler.

2. Remove the siphon.

3. Fill the siphon with water. 

The siphon must be filled up to the level markers.

4. Put the siphon back in place.

5. Fill the central heating system.

6. Start up the boiler.

12 Decommissioning

118

7609474 - v02 - 04092014

Содержание POWER HT+ 1.110





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды