Baxi POWER HT+ 1.110 Скачать руководство пользователя страница 117

Страница: 117 / 124

Display

Description of the error

430

430:Dyn water pres too low

Safety cut-off for absence of circulation (check made by a

pressure sensor)

Note

1. This list is not exhaustive. Other error codes may be dis

played. Contact the accredited technical assistance service.

2. If the display of the error code persists, contact the accredited

assistance service.

Note

If the error code simultaneously displays the and symbols,

contact the accredited technical assistance service.

11.1.1 Automatic error code clearing

If the symbol is displayed at the same time as the error code, the error

code is automatically cleared when the cause that prompted it stops.
A flow or return temperature in excess of the critical value prompts an er

ror code. The error code is automatically cleared when the temperature

drops below the critical value.

11.1.2 Clearing error codes

If the probable cause of an error code is resolved but the error code con

tinues to be displayed, proceed as follows to clear the error code:

1. Press the button.

The command R

Reset? Yes is displayed on the control panel.

2. Confirm by pressing the button.

The error code disappears after a few seconds.

11 Troubleshooting

7609474 - v02 - 04092014

117

Содержание POWER HT+ 1.110





























































































































Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды

Baxi POWER HT+ 1.110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание POWER HT+ 1.110

Отзывы:

Бренды по названию

Популярные бренды