Axel WOLF 1MS Скачать руководство пользователя страница 97

Страница: 97 / 229

14.6.17

Audio DEV (Silence detector)

This page allows the user to set mainly the silence threshold and timing, for each single Channel / Frequency.

NAME

DESCRIPTION

NOTE

Chan

Channel Number

Chan Label

Mnemonic name that can be applied to the Channel / Frequency

Frequency

Frequency corresponding to the Channel, expressed in MHz

Preset

String used by the configurator

Scan Time

This value represents the time in s that the tuner remain on this frequency.

Chan Mask

This control allow (or not) the channel to be under control.

If it is masked,
the channel is
NOT under
control

Silence Thr

This is the minimum level to be considered

audio

. Under this threshold the audio is

considered “silence”.

See Note1
reported
below

Silence Time

This parameter is related to Silence Thr, after this <Silence Time> the incoming
audio is considered “Silence”

Silence Hold

is the time between the cessation of the alarm condition and alarm signaling finished

Silence Mask

It is possible to set, for each single parameter: unmasked, masked, severity-1,
severity-2, severity-3, RFL2 mask.

Silence Email

In case the alarm/error raise up, the Wolf 2MS sends an email if <enable>.
If is <disable> no action are taken.

Silence Trap

In case the alarm/error raise up, the Wolf 2MS sends a trap if <enable>.
If is <disable> no action are taken.

Silence Label

This is the label/content that the user can choose to shows via email or in the trap in
case of error.

Содержание WOLF 1MS






































































































































































































































Результаты поиска

Содержание WOLF 1MS

Отзывы:

Axel WOLF 1MS, Руководство пользователя, Страница: 97 / 229

Результаты поиска

Содержание WOLF 1MS

Отзывы: