Axel WOLF 1MS Скачать руководство пользователя страница 109

Страница: 109 / 229

109

14.6.27

RDS TA (Traffic Announcement)

NAME

DESCRIPTION

NOTE

Chan

Channel Number

Chan Label

Mnemonic name that can be applied to the Channel / Frequency

Frequency

Frequency corresponding to the Channel, expressed in MHz

Preset

String used by the configurator

Scan Time

This value represents the time in s that the tuner remain on this frequency.

Chan Mask

This control allow (or not) the channel to be under control.

If it is masked,
the channel is
NOT under
control

MaxOn Timeout

When TA is ON for a time greater than

MaxOnTimeout

value, an alarm is reported.

If timeout = 0 no alarms are reported

Value
expressed in
Seconds

NoVarTimeout

This parameter launches an alarm if there is not a change in the TA for a certain
period. This NoVarTimeout is useful to monitor the radio stations that are using TA.

Value
expressed in
minutes

Mask

It is possible to set, for each single parameter: unmasked, masked, severity-1,
severity-2, severity-3, RFL2 mask.

Email

In case the alarm/error raise up, the Wolf 2MS sends an email if <enable>.
If is <disable> no action are taken.

Trap

In case the alarm/error raise up, the Wolf 2MS sends a trap if <enable>.
If is <disable> no action are taken.

Label

This is the label/content that the user can choose to shows via email or in the trap in
case of error.

Содержание WOLF 1MS






































































































































































































































Результаты поиска

Содержание WOLF 1MS

Отзывы:

Axel WOLF 1MS, Руководство пользователя, Страница: 109 / 229

Результаты поиска

Содержание WOLF 1MS

Отзывы: