Axel WOLF 1MS Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 229

Axel WOLF 1MS Скачать руководство пользователя страница 36

WOLF 2MS GENERAL DESCRIPTION

| WOLF 2MS GENERAL DESCRIPTION

36

12.3 WOLF 2MS REAR PANEL

N°

CONTROL NAME

FUNCTION

1

POWER SUPPLY UNIT

Power inlet with integrated switch on/off. The switch-power socket unit
is protected via fuse placed directly over the switching power supply.
The fuse is a retarded type 2000 mA for 230V mains voltage. Please
refer to

“Fuse Replacement”

in order to replace the fuse.

2

RF ANTENNA IN 1 - 2

RF antenna input -1 for Tuner -1 and RF antenna input -2 for Tuner -2.
The connection provided is over BNC unbalanced 50

Ω

3

ANALOG INPUT

External Input

source in analog Left + Right. The user can connect to

this input, an audio source to be monitored and under control. This
audio

input

is

continuously

monitored:

silence

detection

(Threshold/time and level), left and right presence, peak left, peak
right.

4

ANALOG OUTPUT

Wolf  2MS  analog  audio  output,  electronically  balanced,  on  XLR
balanced  stereo  connector.  This  audio  output  presents  the  capability
to listen the Tuner -1 or the Tuner -2 output software selectable.

5

DIGITAL AES/EBU

External Input

source in/out digital in AES/EBU format. The user can

connect to this input, an audio source. This audio input is continuously
monitored:  silence  detection  (Threshold/time  and  level),  left  and  right
presence,  peak  left,  peak  right.  The  digital  output  presents  the
capability  to  listen  the  Tuner  -1  or  the  Tuner  -2  output  software
selectable.  The  audio  output  is  over  XLR  electronically  balanced
connection.

6

ETHERNET

Double  Ethernet  port  over  Rj45  connectors.  The  port  n°1  is  used  to
connect  the  device  to  a  LAN  network  and  upload  or  download
configurations  and  settings.  The  port  n°2  is  used  an  audio streaming
port.

«
...
34
35
36
37
38
...
»

Содержание WOLF 1MS






































































































































































































































Отзывы:

Нет отзывов