manualshive.com logo in svg

Axel WOLF 1MS, Руководство пользователя, Страница: 211 / 229

Поделиться
Скачать
Axel WOLF 1MS Скачать руководство пользователя страница 211

TECHNICAL APPENDIX

 

 

 

      | TECHNICAL APPENDIX 

211 

 

 

 
 
Tested in SmartScan with the same setup depicted above for ‘normal’ Scan Mode. 
If an alarm condition is found on a channel, instead of state an alarm condition, system stops on channel for a period 
(depending on tested service that cause alarm condition) collecting more data. In this state no alarm or Trap was 
reported. The Channel Memory 

index reports the cause(s) of the stop (see below: “1 of 3 (RTP)”). 

 
 

 

 

If a valid (no alarm) condition is found in this time, system unlocks and normal scan reprises. 
If no valid condition is found, system unlocks, normal scan reprises and an alarm condition and/or a trap is reported (see 
above). 
Note that Channel Memory reports normal index display (“1 of 3”). 
 
If alarm condition persists, after a while the system stops again on channel and the procedure restarts (note that now the 
alarm condition status ON persists). 
 

Содержание WOLF 1MS






































































































































































































































Отзывы:

Нет отзывов