Axel WOLF 1MS Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 229

Axel WOLF 1MS Скачать руководство пользователя страница 63

WOLF 2MS WEB PAGE

| WOLF 2MS WEB PAGE

63

13.2.3

Note about NTP Settings and behavior

To activate the NTP auto synchronization set a not zero value in AutoRequest Time. After a modification of this
parameter or a modification of the NTP IP address, the Wolf2MS will try to synchronize the system clock. After the first
synchronization, the server will be contacted automatically with the selected period in minutes.

After a system reboot or restart, if AutoRequestTime is activated, in the first operative minute the NTP-V3 server will be
contacted, as well as after the selected period.

The NtpSynch status starts as OK (synchronized) at the system startup, but after the first synchronization attempt it will
show the real status. Every NtpSync status variation is signaled (if enabled) with the NtpFailureNotificationTrap.

An NTP synchronization failure will be indicated with a red alarm line under the Date/Time field. Moreover, Date and time
will blink in the display panel in case of synchronization failure.

Starting from Fw release 1.0.4 the NTP behavior has been modified. Wolf 2MS tries for 3 minutes a replies from the NTP
server before reporting an error. In previous release Wolf 2MS replies immediately about the NTP loss. In case of alarm,
Wolf 2MS tries each single minute until Wolf 2MS gets a reply from NTP server.

With this new feature, random errors caused by NTP loss are no longer reported. No more parameters have been added
to mask this kind of alarm.

«
...
61
62
63
64
65
...
»

Содержание WOLF 1MS






































































































































































































































Отзывы:

Нет отзывов