Axel WOLF 1MS Скачать руководство пользователя страница 132

Страница: 132 / 229

132

14.1 AUDIO 1 - SETUP

This section allows the user to configure the audio source delivered to the Audio Streamer Module.

Audio1 Source:

This setting allows to

deliver to the Audio-1 stream module, an
audio source that can be selected between
Tuner-1 or Tuner-2 or Analog or Digital.
It is also possible to

Audio1 Signal Name:

it is possible to apply

a name to the signal delivered to the
streamer.

Stream Source Gain:

is the gain that is

applied to the Audio Source. The admitted
values are between -20.0 dB and +20.0 dB
in 0.1dB steps.

Stream1 Encoder

: it is possible to decide

what type of audio encoder to use for the
streaming.

Stream1 BitRate:

in this setup it is possible

to decide the audio encoding bitrate

Stream1 Mode

: it is possible to choose if the

streaming is Mono or Stereo

Содержание WOLF 1MS






































































































































































































































Результаты поиска

Содержание WOLF 1MS

Отзывы:

Axel WOLF 1MS, Руководство пользователя, Страница: 132 / 229

Результаты поиска

Содержание WOLF 1MS

Отзывы: