manualshive.com logo in svg

Axel WOLF 1MS, Руководство пользователя, Страница: 31 / 229

Поделиться
Скачать
Axel WOLF 1MS Скачать руководство пользователя страница 31

WOLF 2MS INSTALLATION NOTE AND FIRST STEP

 

 

 

      | WOLF 2MS INSTALLATION NOTE AND FIRST STEP 

31 

 

11 

WOLF 2MS INSTALLATION NOTE AND FIRST STEP 

 

Best setup location  

The Wolf 2MS 

should be installed in a 19” rack. Avoid direct sunlight, close proximity to radiators and air conditioning, 

dust, water, and chemicals. Choose a rack location that permits a clear view to the indicators on the device and ensure a 
sufficient heat dissipation of the device.  
 

Power supply  

The device is designed for operation with 100 to 240 V AC, 50 Hz to 60 Hz. Check the corresponding device labelling for 
compatibility to the domestic line voltage and frequency before connecting the IEC power connector to the mains supply!  
 
 

 

WARNING

 

Disconnect  mains  power  plug  before  you 
open  the  housing.  Repair  of  the  equipment 
must  only  be  carried  out  by  authorized  and 
qualified personnel.

  

 

 

 

1 

 

Power Supply 

 
Please make sure that the device and the contained fuse(s) (please see 
p. 20) are compatible to the domestic line voltage and frequency. If the 
device  is  compatible,  connect  the  power  supply  cord  fully  to  the  IEC 
power  connector  at  the  rear  side  of  the  device  and  a  mains  power 
outlet. 

The “LCD Screed” will then turn on.  

 

 
2 

 
Network configuration  
 

 
For  delivery,  the  device  is  configured  with  default  settings  for  the  first 
connection via the IP interface.  
Wolf  2MS  have  a  display,  so  you  can  configure  the  IP  settings  right 
now:  
See step 

“

LAN-1 Page Functionality (How to set the TCP/IP ETH-1)

” 

 

 
3 

 
Connect to network  
 

 

Connect a network patch cable to the “10/100-Base-T” connector on the 
rear side of the device and your existing IP network.  

 

 
4 

 
Web interface  
 

 
The  device  can  be  fully  operated  with  an  internet  browser  via  the 
integrated web interface. Use a computer that is connected to the same 
IP  network  that  the Wolf  2MS  device  is connected  to.  Start  an internet 
browser,  Firefox/Mozilla  >V2.0  Google  Chrome  both  with  Java  Script 
activated and enter the configured IP address in the address bar of the 
browser. If the IP address has not been changed in step 2, please enter 
the  default  address  in  the  address  bar  of  the  browser: 
192.168.XXX.XXX.  

 

 
5 

 
Connect FM antenna 
cable to each Tuner-1 
and Tuner-2 
 

 
Now  connect  the  antenna  cable  to Wolf  2MS.  There  are  two  separate 
BNC  inputs,  please  provide  a  correct  level  of  RF  signal  to  the 
equipment. See in the technical specs the RF level range.  

 

 
6 

 
Ready!  
 

 
These  first  steps  are  only  intended  for  a  quick  first  start  and  do  not 
cover all device functions. Pease read carefully the entire manual to be 
able to use all functions of the device.  
 

 
7 
 

 

Important note on the 
Username and password  

 

 
The  equipment  comes  out  from  Axel  Technology  with  a  standard 
username: admin and password: admin 
Each  time  a  NEW  user,  with  administration  rights  is  created,  the  user 

admin

  disappear  and  it  is  replaced  by  the  new  one  just  created.  If  all 

users are deleted, the standard admin 

– admin comes out again 

 

Содержание WOLF 1MS






































































































































































































































Отзывы:

Нет отзывов