Axel WOLF 1MS Скачать руководство пользователя страница 226

Страница: 226 / 229

TECHNICAL SPECIFICATION WOLF 2MS

| TECHNICAL SPECIFICATION WOLF 2MS

226

Sample rates

32 kHz / 44.1 kHz / 48 kHz / 96 kHz with src and jitter correction

Operative Nominal level:

From 0.0 dBFs to -24dBFs (0.1 dBu step)

Dynamic Range:

125 dB (Typ)

Distortion

less than 0.01% TDH+Noise (-20dBFs@ 1Khz)

Input Modes:

Stereo, Mono (Left), Mono (Right), Mono (Left+Right)

ANALOG INPUT MODULE

A/D Conversion

24bit Sigma-Delta Conversion

– 32kHz sample rate

Connectors:

XLR, female - Electronically balanced

AD Clipping Point

+20.0dBu

Operative Nominal Level:

From

–12.0dBu to +12.0dBu (0.1dBu Step)

Line Impedance

10 kΩ (Electronically balanced selectable) EMI–suppressed

Distortion:

less than 0.02% TDH+NOISE (0.0dBu @ 1Khz)

AD Dynamic Range:

108 dB RMS (110 dB A-weighted, 20Hz - 15kHz)

Input Modes:

Stereo, Mono (Left), Mono (Right), Mono (Left+Right)

AUDIO & RDS STREAMING MODULES

Protocols

UDP/RTP, TCP/IP, Shoutcast and IceCast2

Encoders

OGG-VORBIS

Interface

Ethernet Port 10/100 Mb/s

Bitrate

User select 24 kbps to 192 kbps

Sample Rates

32Ksamples/sec

RDS Streaming

Proprietary redundant protocol over UDP or RAW-TCP/IP

Administration

User right management

Содержание WOLF 1MS






































































































































































































































Результаты поиска

Содержание WOLF 1MS

Отзывы:

Axel WOLF 1MS, Руководство пользователя, Страница: 226 / 229

Результаты поиска

Содержание WOLF 1MS

Отзывы: