Axel WOLF 1MS Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 229

Axel WOLF 1MS Скачать руководство пользователя страница 101

|

101

14.6.20

Audio MS (Mono Silence)

This page allows the user to set mainly the silence threshold and timing, for Audio Mono inside MPX Signal.
Mono Silence alarm and about 16 new Oids in the Audio Module branches and two new traps. This new alarm rises up
when the audio levels “(RightRms)/2” is under the threshold for a time greater than the silence time. The
threshold range is down to -60dBr. The measurement value is available with all input sources, but the alarms and traps
are available for the Tun1 e Tun2 sources only. MIB L4-0 is required

NAME

DESCRIPTION

NOTE

Chan

Channel Number

Chan Label

Mnemonic name that can be applied to the Channel / Frequency

Frequency

Frequency corresponding to the Channel, expressed in MHz

Preset

String used by the configurator

Scan Time

This value represents the time in s that the tuner remain on this frequency.

Chan Mask

This control allow (or not) the channel to be under control.

Thr

This is the minimum level to be considered

audio

. Under this threshold the audio is

considered “silence”.

Time

This parameter is related to Silence Thr, after this <Validation> the incoming audio
is considered “Silence”

Hold

is the time between the cessation of the alarm condition and alarm signaling finished

Mask

It is possible to set, for each single parameter: unmasked, masked, severity-1,
severity-2, severity-3, RFL2 mask.

Email

In case the alarm/error raise up, the Wolf 2MS sends an email if <enable>.
If is <disable> no action are taken.

Trap

In case the alarm/error raise up, the Wolf 2MS sends a trap if <enable>.
If is <disable> no action are taken.

Label

This is the label/content that the user can choose to shows via email or in the trap in
case of error.

«
...
99
100
101
102
103
...
»

Содержание WOLF 1MS






































































































































































































































Отзывы:

Нет отзывов