Axel WOLF 1MS Скачать руководство пользователя страница 42

Страница: 42 / 229

WOLF 2MS GENERAL DESCRIPTION

| WOLF 2MS GENERAL DESCRIPTION

12.4.7

Alarms Panel Zone Functionality

This Label shows the status of the Alarms panel
This Label shows the status of the Alarms panel

Right LCD Panel

Left LED Panel (Alarm Panel)

The Alarms Panel

(Left LED Panel)

shows:

on the left side the alarms of Tuner module-1

on the right side the alarms of Tuner module-2

In the Right LCD Panel it is possible to find the Alarm Panel label (red square in the picture above) The status of this
label should be:

All Channels - Mode
In AC Mode the LEDs indicate the OR (sum) of the all
same alarm type when the LEDs are on theirs status is
blinking.

Single Channel - Mode
In SC Mode the LEDs indicate only the alarm of the
memory and frequency selected, when the LEDs are on
theirs status is fixed.

This label shows the status of the two areas of alarms panel :

Label

AC-AC

(Tuner-1 and Tuner 2 are in All Channels - Mode)

Label

SC-SC

(Tuner-1 and Tuner 2 are in Single Channel - Mode)

Label

AC-SC

(Tuner-1 is in All Channels - Mode and Tuner 2 is in Single Channel - Mode)

Label

SC-AC

(Tuner-1 is in Single Channel - Mode and Tuner 2 is in All Channels - Mode)

Check the display functionality and

RF ALARM

Status:

Using web page set SCAN mode for the 1

and 2

tuner.

Verify the display status :

AC-AC

Using web server move the RF-H1 threshold of the first memory under the measured value for each tuner.

Verify that the display shows TUNER ERROR, in memory 01 for each tuner.

The first led

RF ALARM

is blinking for each tuner.

Using the the Jog Shuttle move the cursor on the display under the tuner-1 memory number.

Push the Jog Shuttle (To select the function)

Rotate the Jog Shuttle till to set Memory 01

Verify the display status : SC-AC

The first led RF ALARM of Tuner-1 is fixed

The first led RF ALARM of Tuner-2 is blinking

Using the the Jog Shuttle move the cursor on the display under the tuner-2 memory number.

Push the Jog Shuttle (To select the function)

Rotate the Jog Shuttle till to set Memory 01

Verify the display status : SC-SC

The first led RF ALARM of Tuner-1 is fixed

The first led RF ALARM of Tuner-2 is fixed

Содержание WOLF 1MS






































































































































































































































Результаты поиска

Содержание WOLF 1MS

Отзывы:

Axel WOLF 1MS, Руководство пользователя, Страница: 42 / 229

Результаты поиска

Содержание WOLF 1MS

Отзывы: