SIP User's Manual
394
Document #: LTRT-12804
Mediant 800 MSBG
The format attribute can be one of the following:
Continuous:
A steady non-interrupted sound (e.g., a dial tone). Only the 'First Signal
On time' should be specified. All other on and off periods must be set to zero. In this
case, the parameter specifies the detection period. For example, if it equals 300, the
tone is detected after 3 seconds (300 x 10 msec). The minimum detection time is 100
msec.
Cadence:
A repeating sequence of on and off sounds. Up to four different sets of
on/off periods can be specified.
Burst:
A single sound followed by silence. Only the 'First Signal On time' and 'First
Signal Off time' should be specified. All other on and off periods must be set to zero.
The burst tone is detected after the off time is completed.
You can specify several tones of the same type. These additional tones are used only for
tone detection. Generation of a specific tone conforms to the first definition of the specific
tone. For example, you can define an additional dial tone by appending the second dial
tone's definition lines to the first tone definition in the
ini
file. The device reports dial tone
detection if either of the two tones is detected.
The Call Progress Tones section of the
ini
file comprises the following segments:
[NUMBER OF CALL PROGRESS TONES]:
Contains the following key:
'Number of Call Progress Tones' defining the number of Call Progress Tones that are
defined in the file.
[CALL PROGRESS TONE #X]:
containing the Xth tone definition, starting from 0 and
not exceeding the number of Call Progress Tones less 1 defined in the first section
(e.g., if 10 tones, then it is 0 to 9), using the following keys:
•
Tone Type:
Call Progress Tone types:
♦
[1]
Dial Tone
♦
[2]
Ringback Tone
♦
[3]
Busy Tone
♦
[7]
Reorder Tone
♦
[8]
Confirmation Tone
♦
[9]
Call Waiting Tone - heard by the called party
♦
[15]
Stutter Dial Tone
♦
[16]
Off Hook Warning Tone
♦
[17]
Call Waiting Ringback Tone - heard by the calling party
♦
[18]
Comfort Tone
♦
[23]
Hold Tone
♦
[46]
Beep Tone
•
Tone Modulation Type:
Amplitude Modulated (1) or regular (0)
•
Tone Form:
The tone's format can be one of the following:
♦
Continuous (1)
♦
Cadence (2)
♦
Burst (3)
•
Low Freq [Hz]:
Frequency (in Hz) of the lower tone component in case of dual
frequency tone, or the frequency of the tone in case of single tone. This is not
relevant to AM tones.
Содержание Mediant 800 MSBG
