manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 36

TeleBoss 850 2.06.280_STD User Manual 

 

Page 30 

 

CPE Settings  

 

 
TeleBoss 850 - CPE Pages 
A) CPE Page 1 (CPEs 1-16) 
B) CPE Page 2 (CPEs 17-32) 
C) CPE Page 3 (CPEs 33-48) 
D) CPE Page 4 (CPEs 49-64) 
 
Enter your Selection: 
 
TeleBoss 850 - CPE Settings 
A) CPE 1                                [0.0.0.0] 
.. . . 
P) CPE 16                               [0.0.0.0] 
 
Enter your Selection: 
 
TeleBoss 850 - CPE 1 Settings 
A) IP Address                           [0.0.0.0] 
B) Name                                 [] 
C) Description                          [] 
D) Alarm Keep-alive Period (seconds)    [0] 
E) Alarm Threshold                      [1] 
F) Enable SitePath Access               [ON] 
G) SSH to Telnet Bridging               [OFF] 
 

 
Following describes the menu options for configuring CPE Settings.  These settings are only for use with the Asentria 
SitePath secure, unified administration portal software and set up is beyond the scope of this manual.  Contact 

Asentria Technical Support

 for further information.

 

 
IP Address

 sets the IP address of the CPE.  Value is a dotted quad IP address.  Default setting is 0.0.0.0 

 
Name

 sets the name given to the CPE.  The only restriction on the name is that it cannot have any double or single 

quotes ( ' or " ) in it.  (Max length is 24 chars) 

 
Description 

sets a description of what the CPE device is.  The only restriction on the description is that it cannot have 

any double or single quotes ( ' or " ) in it. (Max length is 64 chars) 

 
Alarm Keep-alive Period (seconds)

 set the number of seconds between periodic pings (ping cycle) sent by the T850 

to the CPE to make sure it is "alive“. 1 ping frame is transmitted per CPE per ping cycle.  Values are: 0 to 65535.  
Default setting is 0. 

 
Alarm Threshold 

sets the number of times that the unit receives no response to the keep-alive ping from the device 

before triggering the CPE down event. Values are: 1 to 255.  Default setting is 1. 

 
Enable SitePath Access

 is an ON/OFF toggle to enable SitePath to communicate with the CPE through the unit. 

 
SSH to Telnet Bridging

 is an ON/OFF toggle on CPE 1 thru 4 only, that enables an authorized user to make a Telnet 

connection to a Telnet-only CPE device while on an SSH connection to the T850.  Refer to the 

SSH to Telnet Bridging

 

section in the Features chapter for more information. 
 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды