manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 219

TeleBoss 850 2.06.280_STD User Manual 

 

Page 213 

 

Rev F    

On-board ESJ/ES (Type 3B) port: 
 

 

 

 

 

 

 

EventSensors (Type1) / CCU32/64 (Type1) 

 

Yes.  Connect sensor to Serial Port I/O1 set to ESBUS mode, with an RS232/ES Bus Adapter (part #4162-010). 

 
 

PB1 

 

No 

 

EventSensor (Type2) / ES-CCU32/64 (Type2) 
Yes, connect sensor to on-board ESJ/ES port with an RJ45/RJ45 cable.  If the unit also has a 4SJ expansion card 
installed, then the on-board sensor port is disabled.  Connect the sensor to one of the 4SJ ports instead. 

 

 

 

PB2 
Yes, requires the T850 host to be running version 2.06.290 or higher.  Also, a PB2 is only supported by an on-
board sensor port, so it will not work if connected to a 4SJ port. 
 
SensorJack (Type3) 
Yes.  These sensors terminate with an RJ45 plug so connect directly to the ESJ/ES port.  If using multiple Sensor 
Jack sensors, or with EventSensor (Type2) sensors, use an RJ45 Splitter (part# 4162-011).  
 
Note:  Currently only the SensorJack Temp Sensor is supported by the T850.  Support for the SensorJack 
Temp/Humidity sensor will be coming soon. 
 
Daisy-chaining a SensorJack sensor to an EventSensor (Type2) sensor does not work.  The SensorJack sensor 
must be connected directly to the ESJ/ES port, or to an RJ45 Splitter that routes directly to the port (through other 
RJ45 splitters is OK). 
 
EventSensor (Type1) sensors cannot be daisy-chained with EventSensor (Type2) sensors;  however you can use 
EventSensor (Type1) sensors connected to Serial Port I/O1 

and

  EventSensor (Type2) sensors connected to any 

sensor port simultaneously.  Just make sure the DIP Switches on all are set so that there are no slotting conflicts. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды