Asentria Teleboss 850 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 223

Asentria Teleboss 850 Скачать руководство пользователя страница 20

TeleBoss 850 2.06.280_STD User Manual

Page 14

Getting Connected

Power Up Sequence

On startup, the T850 goes through the following boot sequence in approximately 55 seconds:

1) The power LED flashes once each second for 30 seconds.
2) The LED for Expansion Card 1 go through a 15 second flashing sequence.
3) All LED’s then go off for approximately 5 seconds.
4) Power, Modem (if installed) and Ethernet LEDs light for 5 seconds, then Modem and Ethernet go off.
5) Power LED will blink once every 5 seconds as a "heartbeat" while the T850 is powered on.

Default Passwords

The T850 uses a very flexible system for managing users, passwords, and access rights. By default, the following
fifth user profiles are enabled. Note that if a password is defined without a user name, the profile is defined just by the
user name. All of the default profiles are password-only. All passwords are masked: ********

The default settings are configured to low security for your convenience in setup. It is highly recommended that you
change these passwords and record them in a secure location.

User

Password

Login To

User1

SMDR

Command processor

User2

SUPER

Command processor

User3

ACCESS1

Passthrough/File 1

User4

ACCESS2

Passthrough/File 2

User 11

Username: admin
Password: password

Command processor

The Status Screen

The T850 Status screen is the unit's one-stop informational source. Most of the information that a user would need to
know about the unit is available through this display. This section outlines this data and highlights why it is useful.

TeleBoss 850 2.06.280 STD - Status
Site Name : 850-850000163
Serial Number : 850000163 Eth 1 : STATIC
Date : THU 03/03/2011 IP Addr : 0.0.0.0
Time : 08:02:48 MAC Addr : 00:10:A3:60:02:3E
Memory : 32768K Eth 2 : STATIC
% Full Alarm : OFF IP Addr : 0.0.0.0
No-Data Alarm 1 : OFF MAC Addr : 00:10:A3:60:02:3F
No-Data Alarm 2 : OFF Modem : Yes
Duplex : FULL
-------------------------------------------------------------------------
Port Baud/Etc. Recs Bytes Full Wrap Name
IO1 : 19200,8N1 00000000 00000000 0% OFF I/O 1
IO2 : 19200,8N1 00000000 00000000 0% OFF I/O 2

COMPLETE
>

TeleBoss 850

indicates that this product is the T850, followed by

2.06.280 STD,

the currently loaded firmware

version.

Site Name

is the identifier assigned to each T850 by the end user in the General Settings menu.

Serial Number

is the factory-assigned, unique serial number for this T850.

«
...
18
19
20
21
22
...
»

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды