manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 212

TeleBoss 850 2.06.280_STD User Manual 

 

Page 206 

 

Battery Backup Module 

 
The TeleBoss 850-2 and 850-6 are available with an optional battery backup that provides backup power for the unit 
in the event of power loss. 
 

Setup 

Ensure the battery enable/disable switch is in the 'enable' position. There is no other setup associated with using the 
battery module, nor are there any settings related to it.  

 

Operation 

As long as the battery enable/disable switch is in the 'enable' position, the battery will be available in case of power 
loss. The amount of time that the host unit can run off battery power depends on various things including the state of 
battery charge at the time, and the number and type of optional devices installed in the host unit. 
  
If the unit is running on battery power, and the battery enable/disable switch is changed to the 'disable' position, the 
host unit will immediately shut down. 
 
The host unit cannot be started up from the battery. This is because battery relay (which connects the battery power to 
the system) is open when no power is applied; it gets closed once the unit starts up and the battery manager 
application runs. Only at that point does battery power become available. 
  
The status of the battery module can be determined from the command processor via the battery status command.  
 
Basic Status 
 

 

>

status battery

 

Battery Status 
 
Enable switch position: ON 
Running on battery: YES (0:05:13) 

 

 

Note that the command can also be invoked in a more abbreviated format such as 

"? BATTERY

"

, 

"

STATUSB

"

 or 

even 

"

?B

"

. 

 
When the charging current goes below 100mA, the charging voltage is switched from high (7.35 volts) to low (6.85 
volts).  
 
When running on battery power, if the battery voltage falls below 5.435 volts, the unit shuts down. Several warning 
messages are sent to all open command processors as the battery voltage gets low. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды