manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 12

TeleBoss 850 2.06.280_STD User Manual 

 

Page 6 

 

 

What is a TeleBoss 850 

 

The Basics 

 

 

 

Fig 1:  TeleBoss 850-0 

 

  Note:

 

Functionally, the TeleBoss 850-0 is identical to the T850-2 and T850-6 products, except that it does not 

have expansion bays on the back panel for insertion of different I/O Expansion Cards.  Therefore, references in this 
manual to Expansion Cards (wireless modems, GPS) functions do not apply to the T850-0.  However, the T850-0 
does feature an on-board sensor port for use with Asentria EventSensors, many of which feature the same I/O as 
some of the optional Expansion Cards, so references to contact closures, analog sensors, and relay outputs are all 
applicable to the T850-0. 
 
 

 

 

Fig 2:  TeleBoss 850 (T850-2 on top, T850-6 on bottom) 

 

The T850 is a powerful remote device management system which can collect and forward text records such as those 
used by Call Accounting and Telemanagement billing applications.  These records are collected by the T850 from 
PBX serial ports, and in some cases directly over a TCP/IP connection.   The T850 can also make a passthrough 
connection directly to devices connected on one of its serial ports, and can also connect you via web or Telnet to 
other devices on the same remote network as the T850.  The T850 provides versatile alarm management of text-
based alarms as well as interfaces with environmental monitoring equipment and contact closure alarms at your 
remote site. The T850 is a powerful remote network management solution for Call Accounting systems, Service 
Bureaus, and end users who need to collect PBX data as well as get remote access, and collect alarms from 
equipment at remote sites. 
 
On-board I/O provides serial, Ethernet, and dialup connectivity.  The T850-2 (11-inch) and T850-6 (17-inch) 
models provide two or six expansion slots respectively to allow addition of various communications and 
monitoring interfaces (Expansion Cards). 
 

Communication Methods 

The T850 has a diverse selection of communication methods available for different applications.  The following 
methods can be used to either access the command processor or provide a passthrough connection to devices 
attached to the serial ports.  All methods of connecting to the unit can be secured via password for protection of data 
and hardware. 

  RS-232 serial 

  Telnet 

  Standard modem serial 

  Security callback modem serial 

  SSH 

  HTTP Server 

 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды