manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 116

TeleBoss 850 2.06.280_STD User Manual 

 

Page 110 

 

11.  Select Alarm/Filter Equation and enter 

TEST_FIELD="test”

.  This will cause an event to occur any time the word 

"test" is received. 
12.  Select Actions and enter "

TRAP(1)

" to cause this data event to send a trap to SNMP manager #1, as configured 

below in the Hostname/IP Address menu. 
 

Other Setup

 

 
1. 

Return to the Main Setup Menu, select “Action Definitions”, select “Hostname/IP Address 1” and enter either the 
hostname or IP address of the SNMP Manager where the trap will be sent. 

2.  Go to the Serial Setup Menu for serial port I/O 1 (or whichever port incoming data will be monitored) and set the 

Data Alarm Enable setting to ON.  

3.  Press <CTRL> + C to return to the command processor. 
 

Testing

 

Connect to the unit serially on I/O 1 and type the word 

test

 

followed by <Enter>.  This should trigger the above data 

event, and an SNMP trap should be sent to SNMP Manager #1.  If this is not the case, double check the network and 
data event settings and then call 

Asentria Technical Support

. 

 

 Note:

 

There will be a 30 second delay in alarming if the terminal emulator being used does not send a LF with the 

CR.  This may be circumvented by pressing <CTRL + J> to generate a LF. 
 

 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды