Asentria Teleboss 850 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 223

Asentria Teleboss 850 Скачать руководство пользователя страница 147

TeleBoss 850 2.06.280_STD User Manual

Page 141

30

Segments-Rate 2

368-377

10

R

31

Segments-Rate 3

378-387

10

R

32

Com Type

388

1

NA

33

X25 In Flow Rate

389-390

2

R

34

X25 Out Flow Rate

391-392

2

R

35

Carrier

393-394

2

R

36

Initial Dialed Number

395-424

30

L

37

Waiting Duration

425-429

5

R

38

Effective Call Duration

430-439

10

R

39

Redirected Call Indicator

440

1

NA

40

Start Date-time

441-457

17

NA

41

Acting Extension Number

458-487

30

L

42

Called Number Node

488-492

5

R

43

Calling Number Node

493-497

5

R

44

Initial Dialed Number Node

498-502

5

R

45

Acting Extension Number Node 503-507

5

R

46

Transit Trunk Group ID

508-512

5

R

47

EndOfLine (0x0A)

513

1

NA

The Real Time Client

The client is idle whenever there are no configured OmniPCX settings. After you upload a configuration file for the
first time, type "

IPRC START

" to start the client. Then type "

IPRC STATUS

" or "

IPRC ?

" to check the current status.

It will either indicate a working status (e.g., "Established - awaiting packet") or if something is wrong (e.g., unable to
connect to the OmniPCX, or a certain output field definition doesn't make sense). All output field definitions must
compile correctly in order for the unit to accept the configuration and attempt to connect to the OmniPCX.

Once the client has accepted a valid configuration, it will attempt to connect to the OmniPCX whenever the unit is
reset. If the user manually stops the client with the

IPRC STOP

command, then the client will remain in the idle state

until either the unit is reset or the user enters the

IPRC START

command.

If a new configuration is uploaded while the client is connected to the PBX, then it will:

1. Disconnect from the PBX if the configuration is invalid.
2. Stay connected to the PBX using the new configuration, if the configuration is valid and the PBX IP address or

TCP port did not change.

3. Disconnect from the PBX and reconnect using the new configuration, if the configuration is valid and the PBX IP

address or TCP port changed.

«
...
145
146
147
148
149
...
»

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды