Asentria Teleboss 850 Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 223

Asentria Teleboss 850 Скачать руководство пользователя страница 154

TeleBoss 850 2.06.280_STD User Manual

Page 148

Intecom Telari

Definition

Intecom Telari is IPRC from EADS (f.k.a. Intecom) E and Telari switches. In this method of IP record collection, a
TCP/IP client on the unit attempts connections and accepts CDR via the connection. This method of IPRC differs
from Generic Client in that it employs a proprietary application-layer protocol to transmit records.

Configuration:

TeleBoss 850 - IP Record Collection (IPRC) Setup
A) IP Record Collection [INTECOM TELARI]
B) Store Collected Data In [FILE1]
C) Data Alarm/Filter Enable [OFF]
D) Target Name [IPRC 1]
E) Hostname/IP Address []
F) Port [8186]
G) Connection Interval (minutes) [1]
H) Time Stamping [OFF]

IP Record Collection

sets the protocol to be used to Intecom Telari.

Store Collected Data In

toggles the FILE to which all incoming Syslog data will be stored. Options are FILE1, FILE2,

AUX1, AUX2, and AUX3. Default setting is FILE1.

Data Alarm/Filter Enable

is an ON/OFF toggle to set whether configured Data Alarms or Filters will be applied to the

incoming data. Default setting is OFF.

Target Name

is the name used to identify the switch when an IPRC Connection Lost Alarm is sent via an

AsentriaAlarm. Default setting is IPRC 1.

Hostname/IP Address

sets the hostname or IP Address of the Telari Record Collection Server (RCS).

Port

set the TCP port used by the Telari RCS. Default setting is port 8186.

Connection Interval (minutes)

sets the number of minutes (1

– 65535) to wait before disconnecting an idle

connection. Default setting is 1.

Time Stamping

is an ON/OFF toggle to set whether each individual call record is stamped with the Date and Time

received in the T850. Default setting is OFF.

Commands

Command

Function

IPRC
IPRC STATUS
IPRC ?

Displays a status report of the active IPRC mode.

IPRC Connect Forces the client to connect from a state where it's waiting to connect.
IPRC Start

Causes immediate connection to the server to retrieve any new records and to
resume regular checking. This command is only required if automatic connection
was previously stopped using the IPRC STOP command.

IPRC Stop

Disables automatic connection and terminates any open connection. Automatic
connection is re-enabled if the T850 is restarted.

Status Display

The IPRC command brings up a status report similar to the following report:

Intecom CDR Client
Status: Idle
Time now: 12/16 12:24:10
COMPLETE

«
...
152
153
154
155
156
...
»

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды