manualshive.com logo in svg

Asentria Teleboss 850, Руководство пользователя

Поделиться
Скачать
Asentria Teleboss 850 Скачать руководство пользователя страница 28

TeleBoss 850 2.06.280_STD User Manual 

 

Page 22 

 

Enable EventSensor Reporting Host

 is an ON/OFF toggle to enable this T850 to be a host for EventSensor 

reporting from another Asentria device.  Default setting is OFF. 
 

EventSensor Reporting Host Port

 sets the TCP Port that this T850 will use for receiving sensor reports from 

another Asentria device.  Default setting is 4000. 
 
For a further explanation of EventSensor Reporting, refer to the 

EventSensor Reporting

 section in the Features 

chapter 
 

SNMP Settings 

 

 
TeleBoss 850 - SNMP Settings 
A) SNMP Community                       [public] 
B) Trap Settings 
C) Security Method                      [MD5-DES] 
D) PPP/Trap IP Address Spoofing         [0.0.0.0] 
 

 

SNMP Community

 sets the SNMP community name to use.  Default setting is Public.  (Max length is 23 chars) 

 

Trap Settings

 displays a menu that allows you to configure various Notification settings.   

 

Security Method 

toggles between MD5-DES and SHA-AES to controls whether MD5 and DES, or SHA-1 and AES, 

are used for authentication and privacy, respectively, for for SNMPv3 get/set/trap operations.  Default setting is MD5-
DES.   

 
PPP/Trap IP Address Spoofing

 allows you to configure the IP address to be displayed in an SNMP trap sent over a 

PPP connection.  If undefined, the T850 PPP IP is used.  Default setting is 0.0.0.0 
 
Trap Settings 
 

 
TeleBoss 850 - Trap Settings 
A) Notification Attempts (0=infinite)                [5] 
B) Notification Timeout (seconds)                    [60] 
C) Notification Cycles (0=infinite)                  [10] 
D) Notification Snooze Period (minutes)              [60] 
E) Notification Security Name                        [] 
F) Notification Security Password                    [********] 

 
 

Notification Attempts

 sets the number of attempts (1 to 65535) of sending a notification (trap/inform) per cycle (that 

is, the initial a retries). If this is 0 then there is 1 infinite cycle.  Default setting is 5. 
 

Notification Timeout

 sets the number of seconds (3 to 60) between two attempts to send an SNMP notification in the 

same cycle.  Default setting is 60. 
 

Notification Cycles

 sets the maximum number of cycles (0 to 60) to try per notification action, where one notification 

action corresponds to one "inform" keyword in an action list for an event.  A cycle is a set of notification attempts 
delimited by a successful action delivery or snooze period.  Default setting is 10. 
 

Notification Snooze Period 

sets the time in minutes (1 to 1440) between two SNMP notification cycles for any one 

notification action. That is, if you have two events generate informs, each inform will have its own timeouts for retries 
and cycles, and its own snooze period.  Default setting is 60. 
 

Notification Security Name / Password

 sets the name and password used for authentication when sending 

SNMPv3 traps. (Max length for each is 31 chars) 
 

  Note:

 

SNMP traps are 

not

 a guaranteed means of delivering notifications.  Traps are a one-way IP network 

datagram and the device receiving traps does not acknowledge them.  Therefore, if the trap does not reach its 
intended destination for whatever reason, the sending device has no way of recognizing this and resending the trap. 

Содержание Teleboss 850
































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды